agenda & evening highlights
Day 1 - Tuesday, November 11
| 9:00 - 18:00 |
TechniFair Booths will be open throughout the day (9:00 - 18:00) on Day One of the conference |
| 9:20-9:50 |
Registration |
| 9:55-10:00(5) |
Opening Remarks
Bertrand Saint-martin
President DELMIA JAPAN, LTD. |
| 10:00-10:45(45) |
Special Speech
Philippe Charles
CEO Dassault Systèmes-Delmia Corp. |
| 10:45-11:30(45) |
Special Speech - DELMIA:Live Digital Factory On-Line
Pascal Lecland, Ph.D
Executive Vice President, R&D Dassault Systèmes-Delmia Corp.
With DELMIA V5 Dassault Systemes provides to the Manufacturing community the capacity to define and optimize the production through the Realistic Simulation of the factory in action. Embracing Dassault Systemes strategy, DELMIA V6 delivers enhanced capabilities leveraging the on-line architecture of V6 to serve a larger community and enable better, faster communication to develop leaner production means. With DELMIA V6, the Manufacturing Community will experience the digital factory in a life like environment.
|
| 11:30-11:50(20) |
TechniFair/Break |
| 11:50-12:40(50) |
Key Note - The Global Sharing of Know-How Data by Utilizing the Digital Engineering
Akira Ishihara
Project General Manager Quality & Production Engineerig Dept.
Vehicle Planning & Production Engineering Div.
TOYOTA MOTOR COPORATION
Standardization and Quality Improvement:
In this session, I will introduce our experience of how the Digital Assembly (DA) has been utilized for the pre-production phase of new vehicles as digital engineering. In addition, I will also explain about the importance of sharing know-how information for globalized production, key-points and approaches to improve product quality including our examples, and expectation and request to DELMIA. |
| 12:40-14:00(80) |
TechniFair/Lunch |
| 14:00-14:40(40) |
Case Study - The Approach to Production Simulation in Fuji Electric Group
Takio Ozawa
Corporate Production Planning Depr. MONOTSUKURI Office
Fuji Electric Holdings Co., Ltd.
Assembility Validation and Production Loss Reduction through Line Simulation for Vending Machine Development:
This session introduces utilization of assembility simulations in Fuji Electric Group for new vending machine development including following examples;
1. Assembility validation before mass production
2. Process comparison between assembly variations
3. Line layout validation
In addition, the session also introduces utilization of line simulations for painting/marking and multiple assembly lines to evaluate;
1. Optimized line flow using buffer
2. Daily production plan
3. Seasonally fluctuating plan
Furthermore, as for our future enhancement, current migration progress from ENVISION/ERGO to V5/Human is explained. |
| 14:40-15:00(20) |
TechniFair/Break |
| 15:00-15:40(40) |
Case Study - Professional development promotion of FAW Die
Shang Xiao
Sr. Engineer Product & Technology Dept.
THE DIE MANUFACTURING Co.,LTD OF FAW
DELMIA automobile body in white Digital Manufacturing Solution:
This paper aims to show the Application results of Faw Die Manufacturing Co,.LTD in using Dassault’s Delmia and Catia System Software to Design Auto Body Panel Dies, Welding fixtures. It mainly including the application of a welding process planning, Die and fixture structure design, the secondary development of Delmia-E5 and Catia, etc. We hope that through the introduction can give you an idea of successful application of Delmia software in the field of automotive body in white production.
|
| 15:40-16:00(20) |
TechniFair/Break |
| 16:00-16:40(40) |
Case Study - The Advantage and Vision of 3D Design
Masatoshi Oshima
Director Mechanical Engineering Department Consulting Engineer
SANYO MACHINE WORKS,LTD
Why We Choose DELMIA Automation:
We are now working on a way to develop advanced design methods using 3D tools, aiming for the ideal future, "All devices planned in a virtual factory are automatically output to drawings and manufactured. No manual drawings and PLC programming are necessary."
However, in the 'real' design fields, a number of drawings for devices are still needed and coding/debagging PLC programs are done by manually. To solve those issues, we implemented DELMIA Automation, a powerful solution for device simulations in a virtual environment with real PLC code.
In this session, we will explain why we choose DELMIA Automation and what can be expected.
|
| 16:40-17:20(40) |
Case Study - The Tata / DELMIA Story: A Digital Manufacturing Success
Ganesh Khedkar
Executive, Digital Manufacturing
Tata Technologies Limited
DELMIA Implementation Approach at Tata Motors Ltd:
Tata Motors, of India, with the help of its partner company INCAT, a Tata Technologies Company, has overcome these challenges by deploying Digital Manufacturing for important go-to-market projects and has realized multiple benefits through optimization. Through Digital Manufacturing, the company planners were able to explore newer methods and processes and conduct more experimentation through iteration at the digital phase. This approach has helped the planners to take more risks, with the DELMIA tools to explore options to validate or address those risks.
|
| 17:20-17:30(10) |
TechniFair/Break |
| 17:30-19:30 |
GALA PARTY |
Day 2 – Tuesday, November 12
Room A
| 10:00-10:40 |
ASSEMBLY/HUMAN
Investigation for "MONOZUKURI" process in the virtual factory – Effective investigation and DELMIA products introduction
We propose an effectual usage of investigation method for "MONOZUKURI" process in the virtual factory, and introduce our basic and enhanced features of DELMIA products for realizing easy investigation.
|
| 10:50-11:30 |
Machining
Introduction of DELMIA Multi Axis CAM System and NC Machine Simulation to output NC-Code efficiently.
Introduction of DELMIA NC Machine Simulation that is standard in the verification of multi axis NC-code, and efficient, all-round NC-Code output including CAM system & post processor.
|
| 11:40-12:20 |
AUTOMATION 1
Virtual Commissioning
V5 Automation enables 3D simulation "Virtual Commissioning"connected with PLC(Programable Logic Controller).This session explains purpose & value of "Virtual Commissioning".
|
| 12:20-13:40 |
Break |
| 13:40-14:20 |
ELYSIUM CO.,LTD
"end-to-end 3D data Interoperability Solutions (ASFALIS, CADdoctor) for DELMIA users"
Elysium, who is the end-to-end 3D data Interoperability Solutions Provider, introduce multi-cad interoperability solution (ASFALIS, CADdoctor) in order to utilize 3D data in manufacturing devision to downstream process.
|
| 14:30-15:10 |
AUTOMATION 2
Virtual Control Design
Using V5 Automation, we propose completely new method of Control Design using 3D "Virtual Control Design". We will also show its current and future concept of Control Design.
|
| 15:20-16:00 |
ASSEMBLY/HUMAN
Investigation for "MONOZUKURI" process in the virtual factory – Effective investigation and DELMIA products introduction
We propose an effectual usage of investigation method for "MONOZUKURI" process in the virtual factory, and introduce our basic and enhanced features of DELMIA products for realizing easy investigation.
|
Room B (With Interpreter)
| 10:00-10:40 |
DELMIA Process Engineer
Building a high productive assembly line by practical use of DELMIA Process Engineer
By simulating or comparing sevaral assembly lines, this session will give you an idea of the method to improve productivity by using our planning solution "DELMIA Process Engineer"
|
| 10:50-11:30 |
Work Instructions Composer
Introducing technical illustration solution, DELMIA Work Instructions Composer
Based on the planning information which is saved on the Manufacturing Hub, this session wil give you an idea of delivering a sophisticated technical illustration to the shop floor, by using our new solution, DELMIA Work Instructions Composer.
|
| 11:40-12:20 |
Geometric Asia Pacific Pte.Ltd.
Integrating Delmia with the extended enterprise.(CAD,PDM,PLM,ERP)
Leveraging its partnership with DELMIA and using it's low-cost development center in India to create customized solutions for collaboration and integration between DELMIA and disparate CAD, PDM/PLM, and ERP systems.
|
| 12:20-13:40 |
Break |
| 13:40-14:20 |
Robotics
New function of DELMIA V5 Robotics
We provide information about New function of DELMIA V5 Robotics to customer.
|
| 14:30-15:10 |
Rand Technologies Japan,K.K.
Optimized Manufacturing Tolerances and Variations using 3D Data on CETOL 6σ
Praveen Gomer
Supervisor - PowerTrain Dimensional Management
CHRYSLER LLC
This session provides successful simulation techniques in Chrysler powertrain division for 3D data utilization with CETOL 6σ to perform precise tolerance analysis for manufacturing variations. It also covers their practical methods to obtain optimized results, such as definitions of tolerance parameters, tolerance management, and collaborative design flow with production related divisions.
|
| 15:20-16:00 |
DELMIA V6
The Introduction of Next-Generation DELMIA "V6"
We introduce innovative world of production planning to you using DELMIA V6.
It realizes [collaboration] and [consolidated database].
|
Room C
| 10:00-10:40 |
DASSAULT SYSTEMS K.K.
Design and Manufacturing Collaboration Solution Provided by Dassault Systèmes
In this session, we will introduce our solutions and their new capabilities, and also focus on various advantages thorough collaboration between CATIA and DELMIA products with demonstrations.
|
| 10:50-11:30 |
OMRON Corporation
Effective usage of model development ｂy V5 Automation R18
The new feature and its usage that reduce the preparation man-hour executing virtual commissioning of automation equipments and shop floor control are explained.
|
| 11:40-12:20 |
DASSAULT SYSTEMS K.K.
To support "MONOZUKURI" in a global environment ENOVIA MatrixOne
In order to maintain competitive edgen in a global market, how the good quality, cost shortening of TTM and the rise of a brand image is performed is important. In this session, the V6 architecture and application for supporting the global market of ENOVIA MatrixOne are explained.
|
| 12:20-13:40 |
Break |
| 13:40-14:20 |
DELMIA Process Engineer/QUEST
DELMIA solutions provides manufacturing planning and simulation close to reality
Manufacturing planning variants and strategies planned in DPE and proved by a dynamic flow simulation in QUEST allows the user to find hidden issues and to optimize his line for best in performances and cost.
|
| 14:30-15:10 |
Hewlett-Packard Japan,Ltd.
New Paradigm Solution "HP BladeWorkstation"
The new engineering environment "HP Blade Workstation Solution" which enable "Security" and "effective central control"
|
| 15:20-16:00 |
KYOEI SANGYO CO.,LTD
Utilization of V5 Automation in Designing Production Lines and Cells (Tentative)
In this session, we will explain the way of utilization of V5 Automation in designing production lines or cells to implement front-loading design processes with virtual commissioning during production launch phase and collaboration of mechanical and control systems.
|
|
